What's New in ScreenShaper Software Version 2.00
 Copyright (c) 2003 by Folsom Research, Inc.,
            All Rights Reserved.              


Thank you for using the ScreenShaper products (VMS-100
or VMS-1000).  This What's New file contains important 
information regarding this release. Folsom Research 
strongly recommends that you read the entire document.

Folsom Research welcomes your comments and suggestions.
Please use the information provided in this file to contact
Customer Service or Technical Support.

Note: When printing this document, choose Landscape for 
      page orientation.

___________________
WHAT'S IN THIS FILE

- New Features
- Improved Functionality
- Installation
- Contacting Folsom Research, Inc.

******************** Version 2.00 ***************************
____________
NEW FEATURES

- Additional input and output resolutions:  1280x720, 1280x768
  and 1280x960.  Note that keystoning for these resolutions is
  not supported.

- New command:  IRSP command is added to adjust the input raster. 

______________________
IMPROVED FUNCTIONALITY

- Change the meaning of CAP command.  CAP command is to define 
  the capture region of the input raster.  This command allow 
  the user to zoom into a region of the input raster.  Note that 
  CAP is only available in the Rotation Mode.

- Limit TLCK to cases where the input and output resolution
  and frame rate matches.  


******************** Version 1.05 ***************************
______________________
IMPROVED FUNCTIONALITY

- Improved start up sequence.

******************** Version 1.04 ***************************
____________
NEW FEATURES

-  Addition of Rotation functions into the ScreenSHAPER 
   products.  These functions (Rotation, Flip and Display
   Area) are enabled by selecting the Rotate Operation
   Mode under System Setup Menu

-  DVI input format is automatically detected.

-  New output frame rate of 59.94Hz.

-  Added the Gamma Correction to the front panel menu.

-  Black Level Adjustment of Non-blended region has been 
   added to the Edge Feather Submenu.

______________________
IMPROVED FUNCTIONALITY

-  The system variables are only reset to default if version 
   number change from 1.XX to 2.XX.  The settings of the unit 
   will be preserve on minorsoftware upgrades.

-  Fix the problem of where the RS232 Config were not saved 
   correctly in the previous version.

-  Fix scaling routine to be capable of scaling image more 
   than 50%.

******************** Version 1.03 ***************************
____________
NEW FEATURES

-  Addition of capability to load and store 9 user-defined warp 
   maps that can be recalled with the MAP command.  WARP MAP 
   INDEX has been added in the ScreenSHAPER VMS-100 front panel's output 
   setup menu.

-  The input auto detection distinguishes between 59HZ, 60HZ, 
   75HZ and 85HZ.  Note the H Frequency for 59HZ and 60HZ are 
   close and can be mistaken one for another.  In which case, 
   it is require to adjust the H Total, H Start and V Start 
   for proper input sampling.

______________________
IMPROVED FUNCTIONALITY

-  Front Panel control of HTotal increments/decrements by 2.

-  In addition to output XGA, support keystone warping for 
   output SXGA and SVGA.

******************** Version 1.02 ***************************
____________
NEW FEATURES

-  First release for ScreenShaper VMS-1000.

-  For ScreenShaper VMS-100, new mode of warping, "KEYSTONE", 
   where the image is corrected for off-axis projection of 
   0 to 25 vertical degree and -20 to 20 horizontal degree. 
   "V KEYSTONE" and "H KEYSTONE" are added to the Output 
   Setup menu to select the desired degree of keystone.  
   Each index represents a change of 2.5 degree.

-  RESET command has a new parameter, "F", which restores all 
   system variables to the default settings and reset the gamma 
   LUT that was saved for projector light intensity calibration.

______________________
IMPROVED FUNCTIONALITY

-  Fixed occassional error where enabling the output raster box on 
   digital input will cause the lost of the image.  

____________
INSTALLATION

Refer to the upgrade_instructions.txt file contained in the 
VMS1000_Rev###.exe file for instructions on upgrading your 
ScreenShaper system to this release of software.

__________________________
CONTACTING FOLSOM RESEARCH

Should you have any comments or questions about this release or any
other product, please contact the factory using one of the following
methods:

____________________
In the United States

Toll Free:    1-888-414-SCAN
                        7226

Phone Number: 1-916-859-2500

Tech Support: 1-866-FRI-SUPT (24hours/7days)
              1-866-374-7878

FAX:          1-916-859-2515

EMAIL:        support@folsom.com

_________
In Europe

Folsom Research BV:
Chromiumweg 111
3812 NM Amersfoort
The Netherlands

T: +31 33 4651555
F: +31 33 4627500
M: +31 6 20005591

EMAIL: saleseurope@folsom.com